-
The fixture price is the smallest number on the page
-
Comparing unit prices is like buying a car and ignoring delivery
-
How much does it cost to install a light fixture?
-
The BEGA bollard light lesson
-
Zigbee lighting changes the math
-
Are BEGA lighting reps worth the markup?
-
What about decorative lights chandelier budgets?
-
"So why not just buy the cheap ones?"
-
What I actually budget now
The fixture price is the smallest number on the page
I manage procurement for a mid-sized build firm — about 300 people, a couple hundred projects a year, and a lighting spend big enough that I keep it in its own tracking sheet. Over the past six years I've logged more than 400 lighting orders, from single downlight replacements to full campus retrofits.
Here's what I keep learning the hard way: the unit price doesn't predict my actual cost. Not even close.
Some projects where we haggled every fixture down to $60 blew their budget by 40%. Other projects where we barely negotiated anything landed right on the number. The difference is almost never in the fixture. It's in installation, controls, and spec coordination — the things we used to treat like afterthoughts.
I'm writing this because I wasted about two years of quote-comparing before I figured it out. You don't have to.
Comparing unit prices is like buying a car and ignoring delivery
In April 2023, we bid an outdoor landscape retrofit. Two vendors quoted. Vendor A's fixtures were $185 each. Vendor B's were $240. We went with A to save about $7,700 on paper.
The job closed $4,100 over budget. Why? A's fixtures needed a separate, matched driver that wasn't in the quote, and their dimming curve didn't play nice with the control box already on site. Rewiring plus a second commissioning visit ate the difference and then some.
When I put those two quotes side by side afterward — same spec sheet, same lumen output, nearly identical fixtures on paper — I finally understood what I'd been getting wrong for years. I'd been pricing a component when I should have been pricing a system.
How much does it cost to install a light fixture?
Nobody on the buy side knows, and that's the whole problem.
According to the U.S. Bureau of Labor Statistics (May 2023 OES data), the median hourly wage for electricians sits around $30. But that's not what an electrician bills. Contractor charge-out rates typically run 2 to 3 times the wage — so roughly $60–$110 an hour on site, depending on region and job type. Verify current rates in your market; labor pricing moves.
Here's the rough ballpark I use for planning, drawn from our own job logs and a few friendly GCs willing to share numbers:
- Recessed downlight, existing wiring: 30–45 minutes per fixture
- Outdoor wall luminaire with weather sealing: 45–90 minutes
- Ground or path light including trenching and splicing: 2–4 hours
- Any fixture with a remote driver that needs a mounting location: add 15–30 minutes just to place the driver
So installation alone runs roughly $40–$120 for a downlight and $250–$500 for a landscape fixture, before you count drywall repair, waterproofing, or conduit. That spread is wider than the gap between most competing fixtures — which is exactly why comparing fixtures in isolation is a losing game.
The BEGA bollard light lesson
Two years ago we used BEGA bollard lights on a landscape project. On paper it looked expensive — roughly $300 a unit against about $130 for a comparable non-spec-grade bollard.
What changed my mind was the third quarter. The cheaper units started yellowing. Half of them developed seal issues around the anchor bolts. Two had drivers fill with water and fail outright. We replaced 14 units under warranty, but labor came out of our pocket — about $2,300 — and the warranty paperwork ate hours of my assistant's time every month for six months.
People think spec-grade fixtures cost more because they're better. Actually, it's closer to the reverse. They can command the price because they rarely force a return trip. The quality is what makes the return trip rare, and the return trip is where the money actually goes.
That's the piece most spreadsheet comparisons miss. You're not paying for a nicer surface finish. You're paying to not send a crew back in eighteen months.
Zigbee lighting changes the math
Control protocol is the quiet budget killer. Zigbee lighting runs on the IEEE 802.15.4 standard at 2.4 GHz, builds a mesh network, and doesn't need dedicated control wiring. In theory that should save you a fortune in cable and conduit.
In practice it only saves you that fortune if everything on site is speaking the same language.
We had a project where Zigbee wall panels, 0–10V drivers, and a couple of DALI dimmers ended up on the same floor because different subcontractors bought what they thought was right. Commissioning turned into its own line item — close to $5,000 — and that wasn't material cost. It was re-terminating, re-pairing, re-programming, and training the property manager on a system that shouldn't have needed training.
"The cheapest five minutes in any lighting project is the one where you confirm the protocol before anyone buys anything."
Now we treat protocol as a pre-purchase decision, not a post-install discovery. It's one line in the spec that saves four figures downstream.
Are BEGA lighting reps worth the markup?
I have mixed feelings about spec reps. On one hand, a BEGA lighting rep brings photometric data, mounting details, and accessory availability I can't extract from a catalog. On the other hand, once a manufacturer is written into the spec, switching later means redesign — and a rep who knows that has very little incentive to compete on price.
What we do now: involve the rep during design, then treat them as a support channel during construction. It hasn't saved us a single dollar on the buy side. It has saved us two spec reversals and one very expensive change order.
Not ideal, but workable. The bottom line for me isn't the rep's rate — it's the cost of the one time they aren't there when the install crew has a question at 7 a.m.
What about decorative lights chandelier budgets?
Decorative lighting looks like a different problem, but the core question is the same. A chandelier might cost $800 at the buy stage. That's not your number. The number is: does the ceiling structure support it, who's deciding the drop height, and is there a service access panel?
I've had this conversation more times than I can count. On a recent hospitality project, a decorative fixture that quoted at $640 consumed about six labor hours plus a structural consult. Install cost alone was north of $1,400. The fixture was the cheap part of the fixture.
"So why not just buy the cheap ones?"
I've genuinely considered it. Buy basic, replace when they die.
The math doesn't hold, though — because on LED fixtures, failure rarely happens at the lamp. It happens at the driver, the thermal path, or the seal. Those failures show up at 18 to 36 months. And every replacement means a return visit, a re-mount, and often redoing the waterproofing that failed in the first place.
There's also an administrative cost nobody puts in the spreadsheet: if a fixture fails under warranty, you still remove it, photograph it, file the claim, and reinstall the replacement. None of that is free.
What I actually budget now
Three rules, applied in this order:
- Estimate install time per fixture before I approve a spec — not after the electrician quotes.
- Confirm the control protocol before anyone writes a purchase order.
- Price the fixture against the number of times I expect to swap it over its life, not against its sticker price.
None of this makes lighting procurement glamorous. It does make it boring — in the best possible way. Boring budgets don't come back to visit you in Q3.
Compare installation first, then fixtures. Once you do, the unit price stops being the headline. It becomes a rounding decision — the kind that costs you nothing and saves you the meeting.
Pricing and labor figures reflect 2023–2024 data and our own project records. Verify current rates and local labor costs before you build a budget on any of these numbers.